Feeling like I am over thinking. My horizontal pieces are level, and my pickets I figure I will keep a straight run until the grade requires I “step up” the next run. Should a run always be post to post? or is 5-8 pickets ok? The right side is me trying to see what it looks like with shorter runs. (i dont think i like it.)
Grade is enough that right side of pic would only be 4’ tall while left is 6’ Ish.
My adhd and lack of self esteem is over thinking this huh? Is “space from top of picket to horizontal piece consistent” a visual plus that is worth something too?
19 Comments
captain_aggravated@sh.itjust.works · 37 pts · 22d
Conventional wisdom is to run the rails parallel to the surface rather than level with gravity:
flandish@lemmy.world · 16 pts · 22d
ohh interesting! then the middle of each picket can be the same distance from the rail. so that side looks consistent too. thanks for your reply!
i might try that. (after all this is only like 4 posts length on this side easy to pop down!)
captain_aggravated@sh.itjust.works · 9 pts · 22d
Happy fencing!
flandish@lemmy.world · 21 pts · 22d
thanks! trying the parallel to ground idea.
bonedaddy@mander.xyz · 10 pts · 21d
Now you're cookin
flandish@lemmy.world · 4 pts · 21d
thanks!
CHOPSTEEQ@lemmy.ml · 5 pts · 21d
Damn man you’re giving me the confidence to take on my fencing project.
flandish@lemmy.world · 3 pts · 21d
thanks! go for it!
klangcola@reddthat.com · 4 pts · 21d
Keeping the pickets vertical like that looks tidy
sepi@piefed.social · 10 pts · 21d
Dude great job so far. These things are difficult the first few times. Good going!
flandish@lemmy.world · 7 pts · 21d
thanks for the kindness!
DarrinBrunner@lemmy.world · 5 pts · 22d
My only comment is I want the top rail horizontal to resist wind load at the top. I like this design, with the top rail being a cap, that protects the endgrain of the pickets. I'm not sure about putting the bottom rail in the dirt, however.
flandish@lemmy.world · 3 pts · 22d
gotcha. thanks!
Montagge@lemmy.zip · 3 pts · 22d
I'd say make it so it looks good to you as long as it'll stay upright!
For the run post to post are you referring to keeping the fence boards level? If so you should be able to lift the boards up to account for grade. Just don't go past your bottom support.
wedge@woodworking.group · 2 pts · 22d
@flandish
If your terrain is irregular along a given panel, you might have to straighten it out a bit so you get level tops without ground interference at bottom anywhere.
If you have two opposing slopes forming a ‘V’ (valley)… well, theoretically that join is possible. :)
flandish@lemmy.world · 4 pts · 22d
thanks! trying this for a bit now that i took the other parts down. bottom gap i am thinking may be a slight too big but i need to landscape around anyway too. for dogs plants etc.
captain_aggravated@sh.itjust.works · 1 pts · 17d
How'd the fence turn out, OP?
flandish@lemmy.world · 1 pts · 17d
hey thanks for asking! i went with the “parallel” option and am getting back to it shortly! (cant send pic at moment but there is one in a comment in thread)
Roofhare@mastodon.social · 1 pts · 22d
@flandish Assuming you want the top of the boards to line up at the same height, I recommend progressively shortening the board at the bottom as the grade of the soil goes up.