One of the first services on my server was nextcloud in docker container from lsio. Never had problems so there was no need to try AIO, but so many people recommend that, it will be my next setup if this one fails me
Enclosure will protect printer from dust and it will also keep the ambient temperature more stable. Dont make it hermetic sealed, better add few holes on the front and few on the back for example. I have a low rpm fan with dust filter because I mostly print PLA and in long prints (12h+) temperature can go a bit too high if there is no airflow at all. Keep in mind that enclosure should be removed sometimes for mintainance, removable sides is what you should look for.
You can leave filament on the printer, but if you dont use it for a long time it could get wet and then you have to dry it. Keep the rest of the spools in plastic sealed box or bag and put some silica gel inside.
Full calibration should be done once, but fine tuning when you face some issues or when you change to different brand or filament type. It depends how well the printer is assembled and how experienced you are, it can take only 5 min every few months, but begginers can spend days sometimes.
Extra tips: clean your rails and wheels whenever you can (once a month at least) for dusty garage. Get a kitchen sponge, drill a hole in it and guide filament trough the hole to remove any dust before extruder.
Daily backup to backblaze b2 and also to local storage with kopia. Its been running for a year I think, no issues at all. I didnt need a real backup yet, just did some restore tests so far
I was asking the same question a year ago and now Im running 30-40 services, all available remotely using VPN.
Everyone is talking about tailscale and how easy it is to setup (never tried it), but I went for pure wireguard VPN and IMO its not complicated at all. I have 3 devices with access to VPN, but I also use reverse proxy NPM (+ pihole as DNS server) just to be able to use custom domain like nextcloud.example instead of typing IP:PORT. I dont feel comfortable with opening ports to public, but had 0 issues with wireguard port opened (so far).
Just giving you an example, other people here might have better advices
My server is diy desktop pc - mbo MSI Z270-A PRO with celeron G3930 and 16GB RAM, 3x SSD on 550W PSU, idles at 23W. After adding another 3.5" HDD consuption went up to 34W. 34W in Ctoatia is around 34€ a year.
Some SFF PCs are at 10-15W. SBCs like rpi should be below 10 W, but dont think you can get anything new for 80€
-4c is extreemly cold, get thermometer inside of enclosure and leave your heatbed on until it reaches 10-15C before you start printing. Even better get enclosure heater. Id also bump nozzle temp to the highest marked on your spool.
Interesting. This is new to me and it looks like it could work. It could be usefull if you print with 0.6 nozzle at 0.6 mm width and then in a corner narrow it down to 0.4 mm
Im not afraid of command line, but also dont feel like linux guy yet. The thing is that installing and using some distros are way easier than windows. I installed POP OS recently and cant believe how smooth and easy it was. Average windows users might not need command line at all on distro like that
Casual users dont get on private trackers hehe. Joking, some guys were posting site that tracks when private trackers have open invites, hope someone will link again. Some trackers are almost impossible to join or keep up with their rules, but like torrentleech should be easy enough.
Ive never used usenet since Im on private trackers for years, but I bet someone can recommend one here.
You can look for older redit posts about recommendation for both, but first decide what contet you are aiming for. Some trackers are just for movies, some are focused on music, but there are also general purpose trackers like torrentleech.
Oh I love this one. How are gateron switches compared to MX? I had shitty romer g on logitech and replaced it with another one with MX and its day and night difference
I went for wireguard VPN instead of exposing services. Its much more safe afaik, but you have to configure each device you want to give access (aka scanning QR code). You also dont need to buy a domain for that.
Exposed services would be easier to use, especially if you want to use it on many devices
One of the first services on my server was nextcloud in docker container from lsio. Never had problems so there was no need to try AIO, but so many people recommend that, it will be my next setup if this one fails me
Correct and sounds like the best of both worlds
You can just cut 30x30 mm peace and zip-tie it over filament 😉
Enclosure will protect printer from dust and it will also keep the ambient temperature more stable. Dont make it hermetic sealed, better add few holes on the front and few on the back for example. I have a low rpm fan with dust filter because I mostly print PLA and in long prints (12h+) temperature can go a bit too high if there is no airflow at all. Keep in mind that enclosure should be removed sometimes for mintainance, removable sides is what you should look for.
You can leave filament on the printer, but if you dont use it for a long time it could get wet and then you have to dry it. Keep the rest of the spools in plastic sealed box or bag and put some silica gel inside.
Full calibration should be done once, but fine tuning when you face some issues or when you change to different brand or filament type. It depends how well the printer is assembled and how experienced you are, it can take only 5 min every few months, but begginers can spend days sometimes.
Extra tips: clean your rails and wheels whenever you can (once a month at least) for dusty garage. Get a kitchen sponge, drill a hole in it and guide filament trough the hole to remove any dust before extruder.
Welcome to the most fun hoby and happy printing!
For 9 disks I would need to print a bigger case, but this one suits me well for now 😉
He is horny 😂
Daily backup to backblaze b2 and also to local storage with kopia. Its been running for a year I think, no issues at all. I didnt need a real backup yet, just did some restore tests so far
I was asking the same question a year ago and now Im running 30-40 services, all available remotely using VPN.
Everyone is talking about tailscale and how easy it is to setup (never tried it), but I went for pure wireguard VPN and IMO its not complicated at all. I have 3 devices with access to VPN, but I also use reverse proxy NPM (+ pihole as DNS server) just to be able to use custom domain like
nextcloud.exampleinstead of typingIP:PORT. I dont feel comfortable with opening ports to public, but had 0 issues with wireguard port opened (so far).Just giving you an example, other people here might have better advices
If OP cant use more than one disk at once, how can they benefit from mergerfs?
In my country pi4 8GB ram with PSU 130€ and then you need SD card and/or SSD
Adding my data as well:
My server is diy desktop pc - mbo MSI Z270-A PRO with celeron G3930 and 16GB RAM, 3x SSD on 550W PSU, idles at 23W. After adding another 3.5" HDD consuption went up to 34W. 34W in Ctoatia is around 34€ a year.
Some SFF PCs are at 10-15W. SBCs like rpi should be below 10 W, but dont think you can get anything new for 80€
Your cpu supports quick sync so I bet you are good without gpu. Try it yourself before buying one, you also drain less power
-4c is extreemly cold, get thermometer inside of enclosure and leave your heatbed on until it reaches 10-15C before you start printing. Even better get enclosure heater. Id also bump nozzle temp to the highest marked on your spool.
Why lower if you print everything at the same layer height?
Interesting. This is new to me and it looks like it could work. It could be usefull if you print with 0.6 nozzle at 0.6 mm width and then in a corner narrow it down to 0.4 mm
Im not afraid of command line, but also dont feel like linux guy yet. The thing is that installing and using some distros are way easier than windows. I installed POP OS recently and cant believe how smooth and easy it was. Average windows users might not need command line at all on distro like that
Casual users dont get on private trackers hehe. Joking, some guys were posting site that tracks when private trackers have open invites, hope someone will link again. Some trackers are almost impossible to join or keep up with their rules, but like torrentleech should be easy enough. Ive never used usenet since Im on private trackers for years, but I bet someone can recommend one here.
You can look for older redit posts about recommendation for both, but first decide what contet you are aiming for. Some trackers are just for movies, some are focused on music, but there are also general purpose trackers like torrentleech.
Oh I love this one. How are gateron switches compared to MX? I had shitty romer g on logitech and replaced it with another one with MX and its day and night difference
I went for wireguard VPN instead of exposing services. Its much more safe afaik, but you have to configure each device you want to give access (aka scanning QR code). You also dont need to buy a domain for that. Exposed services would be easier to use, especially if you want to use it on many devices
Private trackers I seed until Im running out of storage, public ones up to 1.2 ratio.
I used to upload some content, but dont have anything thats not already available anymore.
I did some donations to our fellow pirates tho
Better then pay for usenet instead of VPN. Not sure is 0% enough to protect yourself