Thanks.i guess being all over it means I noticed all the minor imperfections, and only have myself to blame.
Issues. I didn't take the time to choses the wood carefully, so some bits of trim had to be redone because after they were ripped, they twisted quite badly. Even taking time to square up the plywood carcass was challenging. (The full unit is 230 by 180cm) So on my own it was quite difficult. My dad helped me move the carcass, thanks dad!
I think (with this being my first wardrobe) some of the finer points went over my head.... For example. I forgot to take into account clearances for the doors so had to take 3mm of each side to stop them rubbing against each other. Would have been easier to do that in the first place!
I also added 18mm to each side of the drawer fronts so that the would stop against the front of the carcass...But forgot that the top edge has to be shared with the bottom edge of the door. If I ever did this again, instead of two parts I'd separate the drawer boxes, so instead of two boxes, I'd have four. The two wardrobe cavities and the two drawer cavities. Would be less cumbersome to manhandle!
Most of my actual design work is done in the spreadsheet workbench. If I had to, I could design furniture in LibreOffice Calc. But, I use the entire drafting process as a sanity check, to make sure I didn't make any mistakes in order of operations.
Which in fairness... Is exactly what I did at first.
I even did the explored the diagrams.
What I didn't do.... Was modify them after there was several changes in scope. Let's hope I use this is a learning experience. The next time just say right back to the design stage.
Just imagine I used the spreadsheet inside Freecad. I could have even defined clearances and tolerances. But we live in learn
It is indeed. Tool where I wasn't too bad surprisingly. The only tool issue I had was my orbital sanders velcro pad has become worn, but it is getting on in years now.
Surprisingly the selection of drawer slides at my local hardware store were awful. The largest drawer is 60 cm deep, and I wanted the full extension ones.very spendy
It doesn't surprise me at all that the selection of stuff for woodworking at a normal hardware store would be awful. I've barely gotten started in the hobby, but I walked into Highland Woodworking once and it was worlds apart from the shit you find at Home Depot.
Dude, this looks really well done. Some of my favorite gifts had little imperfections, just like all people. It shows a human did it. They will cherish that work, flaws and all, and call it their own. You've created a monument and did it without the human form! Bravo!!
20 Comments
infinitevalence@discuss.online · 39 pts · 65d
Stain or paint and you have a 9/10! Great work.
Setiyeti93@lemmy.ca · 22 pts · 65d
Thanks!. It will be getting painted over the weekend. This was made for someone,, and they've chosen a deep red.
heydo@lemmy.world · 23 pts · 65d
Looks really good! What was the most difficult part? What issues came up? Any advice on how to avoid them?
Setiyeti93@lemmy.ca · 20 pts · 65d
Thanks.i guess being all over it means I noticed all the minor imperfections, and only have myself to blame.
Issues. I didn't take the time to choses the wood carefully, so some bits of trim had to be redone because after they were ripped, they twisted quite badly. Even taking time to square up the plywood carcass was challenging. (The full unit is 230 by 180cm) So on my own it was quite difficult. My dad helped me move the carcass, thanks dad!
I think (with this being my first wardrobe) some of the finer points went over my head.... For example. I forgot to take into account clearances for the doors so had to take 3mm of each side to stop them rubbing against each other. Would have been easier to do that in the first place!
I also added 18mm to each side of the drawer fronts so that the would stop against the front of the carcass...But forgot that the top edge has to be shared with the bottom edge of the door. If I ever did this again, instead of two parts I'd separate the drawer boxes, so instead of two boxes, I'd have four. The two wardrobe cavities and the two drawer cavities. Would be less cumbersome to manhandle!
captain_aggravated@sh.itjust.works · 3 pts · 64d
This right here is why I still use FreeCAD.
Most of my actual design work is done in the spreadsheet workbench. If I had to, I could design furniture in LibreOffice Calc. But, I use the entire drafting process as a sanity check, to make sure I didn't make any mistakes in order of operations.
Setiyeti93@lemmy.ca · 2 pts · 64d
Which in fairness... Is exactly what I did at first.
I even did the explored the diagrams.
What I didn't do.... Was modify them after there was several changes in scope. Let's hope I use this is a learning experience. The next time just say right back to the design stage.
Just imagine I used the spreadsheet inside Freecad. I could have even defined clearances and tolerances. But we live in learn
socsa@piefed.social · 2 pts · 65d
Replacing blades every other cut because MDF is the retard strength of the woodworking field.
wjrii@lemmy.world · 2 pts · 65d
Kills every edged consumable like it was hickory grown in a sand dune, but god forbid you get one drop of sweat on it before you paint...
Tolookah@discuss.tchncs.de · 1 pts · 65d
The doors might be mdf but the box looks ply.
Setiyeti93@lemmy.ca · 1 pts · 64d
It is indeed. Tool where I wasn't too bad surprisingly. The only tool issue I had was my orbital sanders velcro pad has become worn, but it is getting on in years now.
ruuster13@lemmy.zip · 2 pts · 65d
Surely the correct answer to the hardest part is: door and drawer hardware.
potate@lemmy.ca · 9 pts · 65d
Looks pretty incredible to me!
Setiyeti93@lemmy.ca · 4 pts · 65d
Thanks for the positivity. It helps 🙂
CompactFlax@discuss.tchncs.de · 8 pts · 65d
It’s a plywood box.
How hard could it be?
With doors of course. And get some drawer slides and handles at the hardware store.
But it is way harder than that sounds. I built a plyo box and barely can use it because it’s so wobbly.
Your work looks fantastic and you’ve learned from it, so the next one will be different, and better.
Setiyeti93@lemmy.ca · 14 pts · 65d
How hard could it be.
I'm going to have to get that on my tombstone!
Surprisingly the selection of drawer slides at my local hardware store were awful. The largest drawer is 60 cm deep, and I wanted the full extension ones.very spendy
Thanks for your kind words
grue@lemmy.world · 1 pts · 65d
It doesn't surprise me at all that the selection of stuff for woodworking at a normal hardware store would be awful. I've barely gotten started in the hobby, but I walked into Highland Woodworking once and it was worlds apart from the shit you find at Home Depot.
regedit@lemmy.zip · 6 pts · 65d
Dude, this looks really well done. Some of my favorite gifts had little imperfections, just like all people. It shows a human did it. They will cherish that work, flaws and all, and call it their own. You've created a monument and did it without the human form! Bravo!!
Smaile@lemmy.ca · 5 pts · 65d
Snug as a bug
CanadianCorhen@lemmy.ca · 4 pts · 65d
Those look absolutely amazing!
MedicPigBabySaver@lemmy.world · 1 pts · 65d
Zillion times more than I could manage.